MACH221SP-7VC View Datasheet(PDF) - Lattice Semiconductor
Part Name
Description
Manufacturer
MACH221SP-7VC Datasheet PDF : 48 Pages
| |||
MACH111 AND MACH111SP
SWITCHING CHARACTERISTICS OVER OPERATING RANGES1
Parameter
Symbol
Parameter Description
-5
-7
-10
-12
-14
-15
-18
Min Max Min Max Min Max Min Max Min Max Min Max Min Max Unit
tPD
Input, I/O, or Feedback to Combinatorial Output
5
7.5
10
12
14
15
18 ns
tS
Setup Time from Input, I/O, or Feedback D-type 3.5
to Clock
T-type 4
5.5
6.5
6.5
7.5
7
8
8.5
10
12
ns
10
11
13.5
ns
tH
Register Data Hold Time
0
0
0
0
0
0
0
ns
tCO
Clock to Output
3.5
5
6
8
10
10
12 ns
tWL
Clock Width
tWH
LOW 2.5
3
5
6
6
6
7.5
ns
HIGH 2.5
3
5
6
6
6
7.5
ns
External
Feedback
D-type 143
1/(tS + tCO) T-type 133
95
87
80
66.7
54
50
42
MHz
74
62.5
50
47.6
39
MHz
fMAX
Maximum
Frequency Internal Feedback (fCNT)
D-type 182
T-type 167
133
125
100
76.9
91
71.4
69
57
66.6
55.5
53
44
MHz
MHz
No Feedback 1/(tWL + tWH)
200
167
100
83.3
83.3
83.3
66.7
MHz
tAR
Asynchronous Reset to Registered Output
7.5
9.5
11
16
19.5
20
24 ns
tARW
Asynchronous Reset Width (Note 2)
4.5
5
7.5
12
14.5
15
18
ns
tARR
Asynchronous Reset Recovery Time (Note 2)
4.5
5
7.5
8
10
10
12
ns
tAP
Asynchronous Preset to Registered Output
7.5
9.5
11
16
19.5
20
24 ns
tAPW
Asynchronous Preset Width (Note 2)
4.5
5
7.5
12
14.5
15
18
ns
tAPR
Asynchronous Preset Recovery Time (Note 2)
4.5
5
7.5
8
10
10
12
ns
tEA
Input, I/O, or Feedback to Output Enable
7.5
9.5
10
12
14.5
15
18 ns
tER
Input, I/O, or Feedback to Output Disable
7.5
9.5
10
12
14.5
15
18 ns
tLP
tPD Increase for Powered-down Macrocell (Note 3)
10
10
10
10
10
10
10 ns
tLPS
tS Increase for Powered-down Macrocell (Note 3)
7
7
7
7
7
7
7 ns
tLPCO tCO Increase for Powered-down Macrocell (Note 3)
3
3
3
3
3
3
3 ns
tLPEA tEA Increase for Powered-down Macrocell (Note 3)
10
10
10
10
10
10
10 ns
Notes:
1. See “Switching Test Circuit” in the General Information Section of the Vantis 1999 Data Book.
2. These parameters are not 100% tested, but are evaluated at initial characterization and at any time the design is modified where this parameter may be affected.
3. If a signal is powered-down, this parameter must be added to its respective high-speed parameter.
MACH 1 & 2 Families
25
Share Link: 