PIC16C71T-04SS 查看數據表（PDF） - Microchip Technology
零件编号
产品描述 (功能)
生产厂家
PIC16C71T-04SS Datasheet PDF : 176 Pages
| |||
PIC16C71X
Applicable Devices 710 71 711 715
13.2 DC Characteristics: PIC16LC715-04 (Commercial, Industrial)
DC CHARACTERISTICS
Param
No.
Characteristic
Standard Operating Conditions (unless otherwise stated)
Operating temperature 0˚C ≤ TA ≤ +70˚C (commercial)
-40˚C ≤ TA ≤ +85˚C (industrial)
Sym Min Typ† Max Units
Conditions
D001
D002*
D003
D004*
D005
D010
Supply Voltage
VDD 2.5 - 5.5 V LP, XT, RC osc configuration (DC - 4 MHz)
RAM Data Retention VDR
Voltage (Note 1)
- 1.5 - V Device in SLEEP mode
VDD start voltage to VPOR - VSS -
ensure internal
Power-on Reset
signal
V See section on Power-on Reset for details
VDD rise rate to
ensure internal
Power-on Reset
signal
SVDD 0.05 -
- V/ms See section on Power-on Reset for details
Brown-out Reset
Voltage
BVDD 3.7 4.0 4.3 V BODEN configuration bit is enabled
Supply Current
(Note 2)
IDD
- 2.0 3.8 mA XT, RC osc configuration
FOSC = 4 MHz, VDD = 3.0V (Note 4)
D010A
- 22.5 48 µA LP osc configuration
FOSC = 32 kHz, VDD = 3.0V, WDT disabled
D015
Brown-out Reset
Current (Note 5)
∆IBOR - 300* 500 µA BOR enabled VDD = 5.0V
D020
D021
D021A
Power-down Current IPD
(Note 3)
- 7.5 30 µA VDD = 3.0V, WDT enabled, -40°C to +85°C
- 0.9 5 µA VDD = 3.0V, WDT disabled, 0°C to +70°C
- 0.9 5 µA VDD = 3.0V, WDT disabled, -40°C to +85°C
D023
Brown-out Reset
Current (Note 5)
∆IBOR - 300* 500 µA BOR enabled VDD = 5.0V
* These parameters are characterized but not tested.
† Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only
and are not tested.
Note 1: This is the limit to which VDD can be lowered in SLEEP mode without losing RAM data.
2: The supply current is mainly a function of the operating voltage and frequency. Other factors such as I/O pin
loading and switching rate, oscillator type, internal code execution pattern, and temperature also have an
impact on the current consumption.
The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail to rail; all I/O pins tristated, pulled to VDD
MCLR = VDD; WDT enabled/disabled as specified.
3: The power-down current in SLEEP mode does not depend on the oscillator type. Power-down current is
measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
4: For RC osc configuration, current through Rext is not included. The current through the resistor can be esti-
mated by the formula Ir = VDD/2Rext (mA) with Rext in kOhm.
5: The ∆ current is the additional current consumed when this peripheral is enabled. This current should be
added to the base IDD or IPD measurement.
DS30272A-page 114
© 1997 Microchip Technology Inc.
Share Link: 