PIC16C71T-04SS 查看數據表（PDF） - Microchip Technology

零件编号

产品描述 (功能)

生产厂家

PIC16C71T-04SS

8-Bit CMOS Microcontrollers with A/D Converter

Microchip Technology 

PIC16C71X

Applicable Devices 710 71 711 715

13.3 DC Characteristics: PIC16C715-04 (Commercial, Industrial, Extended)

PIC16C715-10 (Commercial, Industrial, Extended)

PIC16C715-20 (Commercial, Industrial, Extended)

PIC16LC715-04 (Commercial, Industrial))

Standard Operating Conditions (unless otherwise stated)

Operating temperature 0˚C ≤ TA ≤ +70˚C (commercial)

DC CHARACTERISTICS

-40˚C ≤ TA ≤ +85˚C (industrial)

-40˚C ≤ TA ≤ +125˚C (extended)

Operating voltage VDD range as described in DC spec Section 13.1

and Section 13.2.

Param

Characteristic

Sym Min Typ Max Units

Conditions

No.

†

D030

D031

D032

Input Low Voltage

I/O ports

with TTL buffer

with Schmitt Trigger buffer

MCLR, RA4/T0CKI,OSC1

(in RC mode)

VIL

VSS - 0.5V V

VSS - 0.2VDD V

VSS - 0.2VDD V

D033

D040

D040A

D041

D042

D042A

D043

D070

D060

D061

D063

OSC1 (in XT, HS and LP)

VSS - 0.3VDD V Note1

Input High Voltage

I/O ports

VIH

-

with TTL buffer

2.0 - VDD V 4.5 ≤ VDD ≤ 5.5V

0.8VDD - VDD V For VDD > 5.5V or VDD < 4.5V

with Schmitt Trigger buffer

0.8VDD - VDD V For entire VDD range

MCLR, RA4/T0CKI RB0/INT

0.8VDD - VDD V

OSC1 (XT, HS and LP)

0.7VDD - VDD V Note1

OSC1 (in RC mode)

0.9VDD - VDD V

PORTB weak pull-up current

IPURB 50 250 400 µA VDD = 5V, VPIN = VSS

Input Leakage Current (Notes 2, 3)

I/O ports

IIL

-

- ±1 µA Vss ≤ VPIN ≤ VDD, Pin at hi-

impedance

MCLR, RA4/T0CKI

-

- ±5 µA Vss ≤ VPIN ≤ VDD

OSC1

-

- ±5 µA Vss ≤ VPIN ≤ VDD, XT, HS and LP

osc configuration

Output Low Voltage

D080 I/O ports

D080A

D083 OSC2/CLKOUT (RC osc config)

D083A

VOL

-

- 0.6 V IOL = 8.5 mA, VDD = 4.5V,

-40°C to +85°C

-

- 0.6 V IOL = 7.0 mA, VDD = 4.5V,

-40°C to +125°C

-

- 0.6 V IOL = 1.6 mA, VDD = 4.5V,

-40°C to +85°C

-

- 0.6 V IOL = 1.2 mA, VDD = 4.5V,

-40°C to +125°C

† Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only

and are not tested.

Note 1: In RC oscillator configuration, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the

PIC16C7X be driven with external clock in RC mode.

2: The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels

represent normal operating conditions. Higher leakage current may be measured at different input voltages.

3: Negative current is defined as coming out of the pin.

© 1997 Microchip Technology Inc.

DS30272A-page 115

Share Link: