COM20022V-HT View Datasheet(PDF) - SMSC -> Microchip
Part Name
Description
Manufacturer
COM20022V-HT Datasheet PDF : 88 Pages
| |||
Additionally, it is necessary to understand the
details of how the other Internal Registers are
used in the transmit and receive sequences and
to know how the internal RAM buffer is properly
set up. The sequence of events that tie these
actions together is discussed as follows.
Selecting RAM Page Size
During normal operation, the 2K x 8 of RAM is
divided into four pages of 512 bytes each. The
page to be used is specified in the "Enable
Transmit (Receive) from (to) Page fnn" command,
where "nn" specifies page 0, 1, 2, or 3. This
allows the user to have constant control over the
allocation of RAM.
When the Offset bit "f" (bit 5 of the "Enable
Transmit (Receive) from (to) Page fnn" command
word) is set to logic "1", an offset of 256 bytes is
added to the page specified. For example: to
transmit from the second half of page 0, the
command "Enable Transmit from Page fnn"
(fnn=100 in this case) is issued by writing 0010
0011 to the Command Register. This allows a
finer resolution of the buffer pages without
affecting software compatibility. This scheme is
useful for applications which frequently use packet
sizes of 256 bytes or less, especially for
microcontroller systems with limited memory
capacity. The remaining portions of the buffer
pages which are not allocated for current transmit
or receive packets may be used as temporary
storage for previous network data, packets to be
sent later, or as extra memory for the system,
which may be indirectly accessed.
If the device is configured to handle both long and
short packets (see "Define Configuration"
command), then receive pages should always be
512 bytes long because the user never knows
what the length of the receive packet will be. In
this case, the transmit pages may be made 256
bytes long, leaving at least 512 bytes free at any
given time. Even if the Command Chaining
operation
is
being
used,
512 bytes is still guaranteed to be free because
Command Chaining only requires two pages for
transmit and two for receive (in this case, two 256
byte pages for transmit and two 512 byte pages
for receive, leaving 512 bytes free). Please note
that it is the responsibility of software to reserve
512 bytes for each receive page if the device is
configured to handle long packets. The
COM20022 does not check page boundaries
during reception. If the device is configured to
handle only short packets, then both transmit and
receive pages may be allocated as 256 bytes
long, freeing at least 1KByte at any given time.
Even if the Command Chaining operation is being
used, 1KByte is still guaranteed to be free
because Command Chaining only requires two
pages for transmit and two for receive (in this
case, a total of four 256 byte pages, leaving 1K
free).
The general rule which may be applied to
determine where in RAM a page begins is as
follows:
Address = (nn x 512) + (f x 256).
Transmit Sequence
During a transmit sequence, the microcontroller
selects a 256 or 512 byte segment of the RAM
buffer and writes into it. The appropriate buffer
size is specified in the "Define Configuration"
command. When long packets are enabled, the
COM20022 interprets the packet as either a long
or short packet, depending on whether the buffer
address 2 contains a zero or non-zero value. The
format of the buffer is shown in Figure 8. Address
0 contains the Source Identifier (SID); Address 1
contains the Destination Identifier (DID); Address
2 (COUNT) contains, for short packets, the value
256-N, where N represents the number of
information bytes in the message, or for long
packets, the value 0, indicating that it is indeed a
long packet. In the latter case, Address 3
(COUNT) would contain the value 512-N, where N
represents the number of information bytes in
50
Share Link: 