PIC16LC924-08/CL View Datasheet(PDF) - Microchip Technology
Part Name
Description
Manufacturer
PIC16LC924-08/CL Datasheet PDF : 189 Pages
| |||
PIC16C9XX
17.3 DC Characteristics:
PIC16C923/924-04 (Commercial, Industrial)
PIC16C923/924-08 (Commercial, Industrial)
PIC16LC923/924-04 (Commercial, Industrial)
DC CHARACTERISTICS
Param
No.
Characteristic
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40˚C ≤ TA ≤ +85˚C for industrial and
0˚C ≤ TA ≤ +70˚C for commercial
Operating voltage VDD range as described in DC spec
Sym Min Typ Max Units
Conditions
†
Input Low Voltage
I/O ports
D030
with TTL buffer
D031
D032
D033
with Schmitt Trigger buffer
MCLR, OSC1 (in RC mode)
OSC1 (in XT, HS and LP)
Input High Voltage
VIL
VSS - 0.15VDD V For entire VDD range
VSS - 0.8V V 4.5V ≤ VDD ≤ 5.5V
VSS - 0.2VDD V
VSS - 0.2VDD V
VSS - 0.3VDD V Note1
I/O ports
VIH
-
D040
with TTL buffer
2.0 - VDD V 4.5V ≤ VDD ≤ 5.5V
D040A
0.25VDD - VDD V For entire VDD range
+ 0.8V
D041
with Schmitt Trigger buffer
0.8VDD - VDD V
D042 MCLR
0.8VDD - VDD V
D042A OSC1 (XT, HS and LP)
0.7VDD - VDD V Note1
D043 OSC1 (in RC mode)
0.9VDD - VDD V
D070 PORTB weak pull-up current
IPURB 50 250 400 µA VDD = 5V, VPIN = VSS
Input Leakage Current
(Notes 2, 3)
D060 I/O ports
IIL
-
- ±1.0 µA Vss ≤ VPIN ≤ VDD, Pin at hi-Z
D061 MCLR, RA4/T0CKI
-
-
±5
µA Vss ≤ VPIN ≤ VDD
D063 OSC1
-
- ±5 µA Vss ≤ VPIN ≤ VDD, XT, HS and LP osc
configuration
Output Low Voltage
D080 I/O ports
VOL
-
- 0.6
V IOL = 4.0 mA, VDD = 4.5V
D083 OSC2/CLKOUT (RC osc mode)
-
- 0.6
V IOL = 1.6 mA, VDD = 4.5V
Output High Voltage
D090 I/O ports (Note 3)
VOH VDD - 0.7 -
-
V IOH = -3.0 mA, VDD = 4.5V
D092 OSC2/CLKOUT (RC osc mode)
VDD - 0.7 -
-
V IOH = -1.3 mA, VDD = 4.5V
Capacitive Loading Specs on
Output Pins
D100* OSC2 pin
COSC2
-
- 15 pF In XT, HS and LP modes when exter-
nal clock is used to drive OSC1.
D101* All I/O pins and OSC2 (in RC)
CIO
-
- 50 pF
D102* SCL, SDA in I2C mode
CB
-
- 400 pF
D150* Open -Drain High Voltage
VDD
-
- 14
V RA4 pin
* These parameters are characterized but not tested.
† Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only
and are not tested.
Note 1: In RC oscillator configuration, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the
PIC16C9XX be driven with external clock in RC mode.
2: The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified lev-
els represent normal operating conditions. Higher leakage current may be measured at different input volt-
ages.
3: Negative current is defined as current sourced by the pin.
DS30444E - page 144
© 1997 Microchip Technology Inc.
Share Link: 