PIC16LC62B-04E/SO View Datasheet(PDF) - Microchip Technology
Part Name
Description
Manufacturer
PIC16LC62B-04E/SO Datasheet PDF : 120 Pages
| |||
PIC16C62B/72A
13.3 DC Characteristics: PIC16C62B/72A-04 (Commercial, Industrial, Extended)
PIC16C62B/72A-20 (Commercial, Industrial, Extended)
PIC16LC62B/72A-04 (Commercial, Industrial)
DC CHARACTERISTICS
Param Sym
No.
VIL
D030
D030A
D031
D032
D033
VIH
D040
D040A
Characteristic
Input Low Voltage
I/O ports
with TTL buffer
with Schmitt Trigger buffer
MCLR, OSC1 (in RC mode)
OSC1 (in XT, HS and LP
modes)
Input High Voltage
I/O ports
with TTL buffer
Standard Operating Conditions (unless otherwise stated)
Operating temperature 0°C ≤ TA ≤ +70°C for commercial
-40°C ≤ TA ≤ +85°C for industrial
-40°C ≤ TA ≤+125°C for extended
Operating voltage VDD range as described in DC spec Section 13.1
and Section 13.2
Min Typ† Max Units
Conditions
VSS
- 0.15VDD V For entire VDD range
Vss
-
0.8V
V 4.5V ≤ VDD ≤ 5.5V
VSS
- 0.2VDD V
Vss
- 0.2VDD V
Vss
- 0.3VDD V Note1
-
2.0
-
VDD
V 4.5V ≤ VDD ≤ 5.5V
0.25VD -
Vdd
V For entire VDD range
D + 0.8V
D041
with Schmitt Trigger buffer
0.8VDD -
VDD
V For entire VDD range
D042
MCLR
0.8VDD -
VDD
V
D042A
OSC1 (XT, HS and LP modes) 0.7VDD -
VDD
V Note1
D043
OSC1 (in RC mode)
0.9VDD -
Vdd
V
Input Leakage Current
(Notes 2, 3)
D060 IIL
I/O ports
-
-
±1
µA Vss ≤ VPIN ≤ VDD,
Pin at hi-impedance
D061
MCLR, RA4/T0CKI
-
-
±5
µA Vss ≤ VPIN ≤ VDD
D063
OSC1
-
-
±5
µA Vss ≤ VPIN ≤ VDD,
XT, HS and LP osc modes
D070 IPURB PORTB weak pull-up current 50
250 400
µA VDD = 5V, VPIN = VSS
Output Low Voltage
D080 VOL I/O ports
-
-
0.6
V IOL = 8.5 mA, VDD = 4.5V,
-40°C to +85°C
* These parameters are characterized but not tested.
† Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only
and are not tested.
Note 1: In RC oscillator mode, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the
device be driven with external clock in RC mode.
2: The leakage current on the MCLR/VPP pin is strongly dependent on the applied voltage level. The specified
levels represent normal operating conditions. Higher leakage current may be measured at different input volt-
ages.
3: Negative current is defined as current sourced by the pin.
DS35008B-page 86
Preliminary
© 1998 Microchip Technology Inc.
Share Link: 