ST72260G1B6/XXX View Datasheet(PDF) - STMicroelectronics

Part Name

Description

Manufacturer

ST72260G1B6/XXX

8-BIT MCU WITH FLASH OR ROM MEMORY, ADC, TWO 16-BIT TIMERS, I2C, SPI, SCI INTERFACES

STMicroelectronics 

ST72260G, ST72262G, ST72264G

TRANSFER OF CUSTOMER CODE (Cont’d)

ST72264 ROM/FASTROM MICROCONTROLLER OPTION LIST

Customer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Address

................................................................................

................................................................................

Contact

................................................................................

Phone No . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Reference /ROM or FAST ROM Code*

ROM or FASTROM code is assigned by STMicroelectronics.

Code must be sent in .S19 format. .Hex extension cannot be processed.

Package/Memory:

SO28:

DIP32:

LFBGA6x6

Die Form:

[ ] 8K (G2M)

[ ] 8K (G2B)

[ ] 8K (G2H)

[ ] 8K (as G2)

[ ] 4K (G1M)

[ ] 4K (G1B)

[ ] 4K (as G1)

Conditioning:

SO package:

Die form:

[ ] Tape & Reel

[ ] Tape & Reel

[ ] Tube

[ ] Inked wafer

[ ] Sawn wafer on sticky foil

Special Marking [ ] No

[ ] Yes “ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _” ( DIP32 15 ch, S028 13 ch, LFBGA6x6 7 ch max.)”

Authorized characters are letters, digits ‘.’, ‘-’, ‘/’ and spaces only.

Temperature Range:

Packaged form: [ ] 0°C to + 70°C

[ ] - 10°C to + 85°C (except LFBGA)

[ ] - 40°C to + 85°C (except LFBGA)

Die form:

Watchdog Selection:

Watchdog Reset on Halt:

LVD Reset

Tested at 25°C only

[ ] Software Activation

[ ] Reset

[ ] Disabled

[ ] Hardware Activation

[ ] No Reset

[ ] Enabled:

[ ] Highest threshold

[ ] Medium threshold

[ ] Lowest threshold

Sector 0 Size:

Readout Protection:

External Interrupt:

Clock Security System:

Clock Source Selection:

PLL1:

[ ] 0.5K

[ ] 1K

[ ] 2K

[ ] 4K

[ ] Disabled

[ ] Enabled

[ ] Port C mapped to ei0 interrupt vector

[ ] Port C mapped to ei1 interrupt vector

[ ] Disabled

[ ] Resonator:

[ ] Enabled

[ ] VLP: Very Low power resonator (32 to 100 kHz)

[ ] LP: Low power resonator (1 to 2 MHz)

[ ] MP: Medium power resonator (2 to 4 MHz)

[ ] MS: Medium speed resonator (4 to 8 MHz)

[ ] HS: High speed resonator (8 to 16 MHz)

[ ] Internal RC Network1:

[ ] External Clock

[ ] Disabled

[ ] Enabled

Comments : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Supply Operating Range in the application: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Notes:

................................................................................

Signature: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1Use of the PLL with the internal RC oscillator is not supported.

Important note: Not all configurations are available. See Table 27 on page 159 for the list of supported part numbers.

160/171

Share Link: