UBA2016AP View Datasheet(PDF) - NXP Semiconductors.

Part Name

Description

Manufacturer

UBA2016AP

600 V fluorescent lamp driver with PFC, linear dimming and boost function

NXP Semiconductors. 

NXP Semiconductors

UBA2016A/15/15A

600 V fluorescent lamp driver

Table 4. Limiting values …continued

In accordance with the Absolute Maximum Rating System (IEC 60134). All voltages referenced to signal ground (GND

pin 15); current flow into the IC is positive.

Symbol

Parameter

Conditions

Min Max Unit

ElectroStatic Discharge (ESD)

VESD

electrostatic discharge

voltage

Human Body Model (HBM)

JEDEC Class 2 for pins: SLHB, IFB, EOL, CIFB,

CPT, IREF, VFB, CF, DIM, BOOST, PH/EN, FBPFC,

COMPPFC, AUXPFC, GPFC, VDD and GLHB

2 +2 kV

JEDEC Class 1C for pins: GHHB, FSHB and SHHB

1 +1 kV

Charge Device Model (CDM)

JEDEC Class 3 for pins: SLHB, IFB, EOL, VFB,

IREF, CIFB, CF, CPT, DIM, BOOST, PH/EN, FBPFC,

COMPPFC, AUXPFC, GPFC, VDD, GLHB

500 +500 V

JEDEC Class 2 for pins: SHHB, FSHB, GHHB

200 +200 V

Latch-up

Ilu

latch-up current

[1] 100 +100 mA

[1] Positive and negative latch-up currents tested at Tj = 150 C by discharging a 22 F capacitor though a 50  series resistor with a

350 H series inductor. Latch-up current values are in accordance with the general quality specification.

9. Thermal characteristics

Table 5.

Symbol

Rth(j-a)

Thermal characteristics

Parameter

thermal resistance from junction to

ambient

10. Characteristics

Conditions

in free air; mounted on a single-sided PCB;

SO20 package

in free air; mounted on a single-sided PCB;

DIP20 package

Typ Unit

100 K/W

90

K/W

Table 6. Characteristics

Tamb = 25 °C; settings according to default setting[1]; all voltages referenced to GND; current flow into the IC is positive;

unless otherwise specified.

Symbol

Parameter

Conditions

Min Typ Max Unit

High voltage

Ileak

Start-up

leakage current

VFSHB = 630 V;

VGHHB = 630 V;

VSHHB = 630 V; VVDD = 0 V

-

-

2

A

Vstartup(VDD)

Vstop(VDD)

Vhys(VDD)

Istb(VDD)

Ipu(stb)(PH/EN)

Vrst(VDD)

start-up voltage on pin VDD

stop voltage on pin VDD

hysteresis voltage on pin VDD

standby current on pin VDD

standby pull-up current on pin PH/EN

reset voltage on pin VDD

VVDD = 11.5 V

Standby or Stop state;

VPH/EN = 0.25 V

11.9 12.4 12.9 V

9.6 10.0 10.4 V

2.1 2.4 2.7 V

0.2 0.24 0.28 mA

7.7 9

10.3 A

3.6 4.2 4.8 V

UBA2016A_15_15A

Product data sheet

All information provided in this document is subject to legal disclaimers.

Rev. 3 — 16 November 2011

© NXP B.V. 2011. All rights reserved.

25 of 42

Share Link: