UBA2016AP View Datasheet(PDF) - NXP Semiconductors.
Part Name
Description
Manufacturer
UBA2016AP
NXP Semiconductors.
UBA2016AP Datasheet PDF : 42 Pages
| |||
NXP Semiconductors
UBA2016A/15/15A
600 V fluorescent lamp driver
Table 6. Characteristics …continued
Tamb = 25 °C; settings according to default setting[1]; all voltages referenced to GND; current flow into the IC is positive;
unless otherwise specified.
Symbol
Parameter
Conditions
Min Typ Max Unit
Rsink(GHHB)
tno
VFd(bs)
Dimming
sink resistance on pin GHHB
non-overlap time
bootstrap diode forward voltage
VSHHB = 0 V; VGHHB = 2 V
IFS = 5 mA
13.5 16
1.25 1.5
1.0 1.5
18.5
1.75 s
2.0 V
Ibias(DIM)
Ri(DIM)
HB protection
bias current on pin DIM
input resistance on pin DIM
VDIM = 1 V
VDIM = 2.5 V
28 26 24 A
-
30 -
k
Vth(sat)(SLHB)
saturation threshold voltage on pin
SLHB
2.35 2.5 2.65 V
td(det)sat
tleb(SLHB)
Iadd(CF)
Ibias(SLHB)
Vth(ocd)(IFB)
saturation detection delay time
Burn state
leading edge blanking time on pin SLHB
additional current on pin CF
bias current on pin SLHB
overcurrent detection threshold voltage
on pin IFB
VSLHB > Vth(sat)SLHB; VCF = 2 V
VSLHB = 2.5 V
-
0.3 -
s
260 340 420 ns
107 96 85 A
10 8.5 7 A
2.8 3.0 3.2 V
Vth(osp)(VFB)
open/short protection threshold voltage
on pin VFB
40 80 120 mV
Vth(ov)(VFB)
overvoltage threshold voltage on pin
VFB
2.4 2.5 2.6 V
tdet(fault)
fault detection time
-
125 -
s
overvoltage extra or capacitive -
50 -
s
mode during burn state
trel(fault)
Vth(ovextra)(VFB)
fault release time
overvoltage extra threshold voltage on
pin VFB
-
1
-
ms
3.2 3.35 3.5 V
Ibias(VFB)
Vth(low)EOL
Vth(high)EOL
Ibias(EOL)
Vth(oveol)(VFB)
bias current on pin VFB
low threshold voltage on pin EOL
high threshold voltage on pin EOL
bias current on pin EOL
overvoltage end-of-life threshold voltage
on pin VFB
VFBPFC = 1.27 V
VFBPFC = 1.27 V
VEOL = 1.9 V
pin DIM open
UBA2015A; UBA2016A
2.3 2.6 2.9 A
1.21 1.27 1.33 V
2.39 2.54 2.69 V
15.4 16.2 17 A
0.8 0.88 0.96 V
VDIM = 1.0 V
UBA2015A; UBA2016A
0.92 1.0 1.08 V
Ven(oveol)(DIM)
overvoltage end-of-life enable voltage
on pin DIM
VDIM = 0.5 V
UBA2015A; UBA2016A
1.15 1.23 1.31 V
0.21 0.25 0.29 V
Vth(hswp)SHHB
hard switching protection threshold
voltage on pin SHHB
fsw = 50 kHz
-
100 -
V
Vth(zvs)SHHB
zero voltage switching detection
threshold voltage on pin SHHB
fsw = 50 kHz
-
30 -
V
Vth(hswr)SHHB
hard switching regulation threshold
voltage on pin SHHB
fsw = 50 kHz
-
100 -
V
UBA2016A_15_15A
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 16 November 2011
© NXP B.V. 2011. All rights reserved.
28 of 42
Share Link: 