UBA2016AP View Datasheet(PDF) - NXP Semiconductors.
Part Name
Description
Manufacturer
UBA2016AP
NXP Semiconductors.
UBA2016AP Datasheet PDF : 42 Pages
| |||
NXP Semiconductors
UBA2016A/15/15A
600 V fluorescent lamp driver
Table 6. Characteristics …continued
Tamb = 25 °C; settings according to default setting[1]; all voltages referenced to GND; current flow into the IC is positive;
unless otherwise specified.
Symbol
Parameter
Conditions
Min Typ Max Unit
Vrestart(VDD)
Irestart(VDD)
Vclamp(VDD)
Iclamp(VDD)
IVDD
restart voltage on pin VDD
restart current on pin VDD
clamp voltage on pin VDD
clamp current on pin VDD
current on pin VDD
PFC normal operation
VVDD = 9 V
IC off; IVDD = 0.33 mA
IC off; VVDD = 14.0 V
VFBPFC = 1.2 V;
VCOMPPFC = 1 V
6.2 6.5 6.8 V
0.85 1.1 1.35 mA
13.0 13.4 13.8 V
25 45 -
mA
1.2 1.7 2.2 mA
ton(PFC)
ton(PFC)high
toff(PFC)low
tleb(FBPFC)
PFC on-time
high PFC on-time
low PFC off-time
leading edge blanking time on pin
FBPFC
VCOMPPFC = 350 mV
VCOMPPFC = Vhigh(COMPPFC)
from the start of rising edge on
pin GPFC
0.6 1
1.4 s
24 28 32 s
1.7 2.0 2.3 s
260 330 400 ns
Vreg(FBPFC)
regulation voltage on pin FBPFC
Ibias(FBPFC)
gm(PFC)
bias current on pin FBPFC
PFC transconductance
Vth(VPFCok)FBPFC PFC voltage OK threshold voltage on
pin FBPFC
VCOMPPFC = 1.6 V
VCOMPPFC = 200 mV
VFBPFC = 1.27 V
VCOMPPFC = 1.5 V;
1.2 V < VFBPFC < 1.34 V
1.23 1.27 1.31 V
1.23 1.28 1.33 V
4.5 5.0 5.5 A
25 30 35 A/V
0.95 1
1.05 V
Vdet(demag)
demagnetization detection voltage
Vclamp(COMPPFC) clamp voltage on pin COMPPFC
PFC protection
on pin AUXPFC
VFBPFC = 1 V
50 100 150 mV
2.85 3
3.15 V
ton(PFC)nodemag
no demagnetization detected PFC
on-time
1.0 1.3 1.6 s
Vth(osp)(FBPFC)
open/short protection threshold voltage
on pin FBPFC
0.2 0.25 0.3 V
Vth(ov)(FBPFC)
overvoltage threshold voltage on pin
FBPFC
1.34 1.39 1.43 V
Ibias(AUXPFC)
PFC driver
bias current on pin AUXPFC
VAUXPFC = 0.1 V
6 5 4 A
Isource(GPFC)
Rsink(GPFC)
HB preheat
source current on pin GPFC
sink resistance on pin GPFC
VGPFC = 4 V; VVDD = 12 V
VGPFC = 2 V; VVDD = 12 V
105 90 75 mA
13.5 16.0 18.5
Rext(PH/EN)
tto(ph)
VO(ph)(PH/EN)
Vctrl(ph)SLHB
external resistor on pin PH/EN
preheat time-out time
CCPT = 100 nF
preheat output voltage on pin PH/EN Preheat or Ignition state
overcurrent protection threshold voltage preheat
on pin SLHB
38.6 -
-
k
0.8 0.94 1.08 s
1.78 1.84 1.9 V
0.44 0.48 0.52 V
Ich(CIFB)
charge current on pin CIFB
no fault detected;
Preheat and Ignition states
only; VCIFB = 1.5 V
10.3 9.0 7.7 A
UBA2016A_15_15A
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 16 November 2011
© NXP B.V. 2011. All rights reserved.
26 of 42
Share Link: 