PIC12F1822T-I/SL 查看數據表（PDF） - Microchip Technology

零件编号

产品描述 (功能)

生产厂家

PIC12F1822T-I/SL

8/14-Pin Flash Microcontrollers with nanoWatt XLP Technology

Microchip Technology 

PIC12F/LF1822/16F/LF1823

REGISTER 23-1: CCP1CON: CCP1 CONTROL REGISTER

R/W-00

R/W-0/0

P1M<1:0>(1)

bit 7

R/W-0/0

R/W-0/0

DC1B<1:0>

R/W-0/0

R/W-0/0

R/W-0/0

CCP1M<3:0>

R/W-0/0

bit 0

Legend:

R = Readable bit

u = Bit is unchanged

‘1’ = Bit is set

W = Writable bit

x = Bit is unknown

‘0’ = Bit is cleared

U = Unimplemented bit, read as ‘0’

-n/n = Value at POR and BOR/Value at all other Reset

bit 7-6

bit 5-4

bit 3-0

P1M<1:0>: Enhanced PWM Output Configuration bits(1)

Capture mode:

Unused

Compare mode:

Unused

PWM mode:

If CCP1M<3:2> = 00, 01, 10:

xx = P1A assigned as Capture/Compare input; P1B, P1C, P1D assigned as port pins(1)

If CCP1M<3:2> = 11:

00 = Single output; P1A modulated; P1B, P1C, P1D assigned as port pins

01 = Full-Bridge output forward; P1D modulated; P1A active; P1B, P1C inactive(1)

10 = Half-Bridge output; P1A, P1B modulated with dead-band control; P1C, P1D assigned as port pins

11 = Full-Bridge output reverse; P1B modulated; P1C active; P1A, P1D inactive(1)

DC1B<1:0>: PWM Duty Cycle Least Significant bits

Capture mode:

Unused

Compare mode:

Unused

PWM mode:

These bits are the two LSbs of the PWM duty cycle. The eight MSbs are found in CCPR1L.

CCP1M<3:0>: ECCP1 Mode Select bits

0000 =

0001 =

0010 =

0011 =

Capture/Compare/PWM off (resets ECCP1 module)

Reserved

Compare mode: toggle output on match

Reserved

0100 =

0101 =

0110 =

0111 =

Capture mode: every falling edge

Capture mode: every rising edge

Capture mode: every 4th rising edge

Capture mode: every 16th rising edge

1000 = Compare mode: initialize ECCP1 pin low; set output on compare match (set CCP1IF)

1001 = Compare mode: initialize ECCP1 pin high; clear output on compare match (set CCP1IF)

1010 = Compare mode: generate software interrupt only; ECCP1 pin reverts to I/O state

1011 = Compare mode: Special Event Trigger (CCP1 resets TMR1, sets CCP1IF bit, and starts A/D conversion

if A/D module is enabled)

PWM mode:

1100 = PWM mode: P1A, P1C active-high; P1B, P1D active-high

1101 = PWM mode: P1A, P1C active-high; P1B, P1D active-low

1110 = PWM mode: P1A, P1C active-low; P1B, P1D active-high

1111 = PWM mode: P1A, P1C active-low; P1B, P1D active-low

Note 1: PIC16F/LF1823 only.

 2010 Microchip Technology Inc.

Preliminary

DS41413A-page 221

Share Link: