ST10F163 View Datasheet(PDF) - STMicroelectronics
Part Name
Description
Manufacturer
ST10F163 Datasheet PDF : 58 Pages
| |||
ST10F163
XVI - ELECTRICAL CHARACTERISTICS
XVI.1 - Absolute maximum ratings
– Ambient temperature under bias (TA): 0 to
+70 °C
– Storage temperature (TST):– 65 to +150 °C
– Voltage on VDD pins with respect to ground
(VSS):– 0.5 to +6.5 V
– Voltage on any pin with respect to ground (VSS):
–0.5 to VDD +0.5 V
– Input current on any pin during overload condi-
tion: –10 to +10 mA
– Absolute sum of all input currents during over-
load condition:|100 mA|
– Power dissipation:1.5 W
Note
Stresses above those listed under “Absolute Maximum
Ratings” may cause permanent damage to the device. This
is a stress rating only and functional operation of the device
at these or any other conditions above those indicated in
the operational sections of this specification is not
guaranteed. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
During overload conditions (VIN>VDD or VIN<VSS) the
Table 15 : DC Characteristics
Parameter
Symbol
Input low voltage
VIL SR
Input high voltage
(all except RSTIN and XTAL1)
VIH SR
Input high voltage RSTIN
VIH1 SR
Input high voltage XTAL1
VIH2 SR
Output low voltage1)
VOL CC
(PORT0, PORT1, Port 4, ALE, RD, WR,
BHE, CLKOUT, RSTOUT)
Output low voltage1
(all other outputs)
VOL1 CC
Output high voltage 1
VOH CC
(PORT0, PORT1, Port 4, ALE, RD, WR,
BHE, CLKOUT, RSTOUT)
Output high voltage 1 2) (all other outputs) VOH1 CC
Input leakage current (all other)
RSTIN pull-up resistor 3)
Read/Write inactive current 4)
IOZ2 CC
RRST CC
IRWH 5)
voltage on pins with respect to ground (VSS) must not
exceed the values defined by the Absolute Maximum
Ratings.
XVI.2 - Parameter Interpretation
The parameters listed in the Electrical Character-
istics tables, Table 15 to Table 18, give the charac-
teristics of the ST10F163 and its demands on the
system.
Where the ST10F163 logic provides signals with
their respective timing characteristics, the symbol
“CC” for Controller Characteristics, is included in
the “Symbol” column.
Where the external system must provide signals
with their respective timing characteristics, to the
ST10F163, the symbol “SR” for System Require-
ment, is included in the “Symbol” column.
XVI.3 - DC characteristics
VDD = 5 V ± 10% VSS = 0 V Reset activeTA = 0 to +70°C
Limit Values
min.
– 0.5
0.2 VDD
+ 0.9
0.7 VDD
0.7 VDD
–
max.
0.2 VDD
– 0.1
VDD + 0.5
VDD + 0.5
VDD + 0.5
0.45
Unit
V
V
V
V
V
Test Condition
–
–
–
–
IOL = 2.4 mA
–
0.9 VDD
2.4
0.9 VDD
2.4
–
50
–
0.45
–
–
±1
250
-40
V
IOL1 = 1.6 mA
V
IOH = – 500 µA
IOH = –2.4 mA
V
IOH = – 250 µA
V
IOH = – 1.6 mA
µA 0 V < VIN < VDD
KΩ
–
µA
VOUT = 2.4 V
31/58
Share Link: 