PIC16F636T-I/SL(2005) View Datasheet(PDF) - Microchip Technology

Part Name

Description

Manufacturer

PIC16F636T-I/SL
(Rev.:2005)

8/14-Pin Flash-Based, 8-Bit CMOS Microcontrollers with nanoWatt Technology

Microchip Technology 

PIC12F635/PIC16F636/639

15.2 DC Characteristics: PIC12F635/PIC16F636-I (Industrial)

DC CHARACTERISTICS

Standard Operating Conditions (unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for industrial

Param

No.

Sym

Device Characteristics

Min Typ† Max Units

VDD

Conditions

Note

D010 IDD

Supply Current(1,2)

D011

D012

D013

D014

D015

—

9 TBD μA

— 18 TBD μA

— 35 TBD μA

— 110 TBD μA

— 190 TBD μA

— 330 TBD μA

— 220 TBD μA

— 370 TBD μA

— 600 TBD μA

— 70 TBD μA

— 140 TBD μA

— 260 TBD μA

— 180 TBD μA

— 320 TBD μA

— 580 TBD μA

— TBD TBD μA

— TBD TBD μA

2.0 FOSC = 32.768 kHz

3.0 LP Oscillator mode

5.0

2.0 FOSC = 1 MHz

3.0 XT Oscillator mode

5.0

2.0 FOSC = 4 MHz

3.0 XT Oscillator mode

5.0

2.0 FOSC = 1 MHz

3.0 EC Oscillator mode

5.0

2.0 FOSC = 4 MHz

3.0 EC Oscillator mode

5.0

2.0 FOSC = 31 kHz

3.0 LFINTOSC mode

D016

D017

D018

— TBD TBD mA

— 340 TBD μA

— 500 TBD μA

— 800 TBD μA

— 180 TBD μA

— 320 TBD μA

— 580 TBD μA

— 2.1 TBD mA

— 2.4 TBD mA

5.0

2.0 FOSC = 4 MHz

3.0 HFINTOSC mode

5.0

2.0 FOSC = 4 MHz

3.0 EXTRC mode

5.0

4.5 FOSC = 20 MHz

5.0 HS Oscillator mode

Legend:

†

Note 1:

2:

3:

4:

TBD = To Be Determined

Data in ‘Typ’ column is at 5.0V, 25°C unless otherwise stated. These parameters are for design guidance

only and are not tested.

The test conditions for all IDD measurements in Active Operation mode are: OSC1 = external square

wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD; MCLR = VDD; WDT disabled. MCU only, Analog

Front-End not included.

The supply current is mainly a function of the operating voltage and frequency. Other factors, such as I/O

pin loading and switching rate, oscillator type, internal code execution pattern and temperature, also have

an impact on the current consumption. MCU only, Analog Front-End not included.

The peripheral current is the sum of the base IDD or IPD and the additional current consumed when this

peripheral is enabled. The peripheral Δ current can be determined by subtracting the base IDD or IPD

current from this limit. Max values should be used when calculating total current consumption.

The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is

measured with the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD.

DS41232B-page 150

Preliminary

© 2005 Microchip Technology Inc.

Share Link: