PIC16F636T-I/SL(2005) View Datasheet(PDF) - Microchip Technology

Part Name

Description

Manufacturer

PIC16F636T-I/SL
(Rev.:2005)

8/14-Pin Flash-Based, 8-Bit CMOS Microcontrollers with nanoWatt Technology

Microchip Technology 

PIC12F635/PIC16F636/639

15.4 DC Characteristics: PIC12F635/PIC16F636-I (Industrial)

PIC12F635/PIC16F636-E (Extended)

DC CHARACTERISTICS

Standard Operating Conditions (unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for industrial

-40°C ≤ TA ≤ +125°C for extended

Param

No.

Sym

Characteristic

Min

Typ† Max Units

Conditions

VIL

Input Low Voltage

I/O ports:

D030

with TTL buffer

VSS

—

0.8

V 4.5V ≤ VDD ≤ 5.5V

D030A

VSS

— 0.15 VDD V Otherwise

D031

with Schmitt Trigger buffer

VSS

— 0.2 VDD V Entire range

D032

D033

D033A

MCLR, OSC1 (RC mode)

VSS

OSC1 (XT and LP modes)(1)

VSS

OSC1 (HS mode)(1)

VSS

— 0.2 VDD V

—

0.3

V

— 0.3 VDD V

VIH

Input High Voltage

I/O ports:

D040

D040A

with TTL buffer

2.0

—

VDD

V 4.5V ≤ VDD ≤ 5.5V

(0.25 VDD + —

VDD

V Otherwise

0.8)

D041

with Schmitt Trigger buffer

0.8 VDD

—

VDD

V Entire range

D042

MCLR

0.8 VDD

—

VDD

V

D043

OSC1 (XT and LP modes)

1.6

—

VDD

V (Note 1)

D043A

OSC1 (HS mode)

0.7 VDD

—

VDD

V (Note 1)

D043B

IIL

OSC1 (RC mode)

Input Leakage Current(2)

0.9 VDD

—

VDD

V

D060

I/O ports

—

± 0.1 ± 1

μA VSS ≤ VPIN ≤ VDD,

Pin at high-impedance

D060A

Analog inputs

—

± 0.1 ± 1

μA VSS ≤ VPIN ≤ VDD

D060B

D061

VREF

MCLR(3)

—

± 0.1 ± 1

μA VSS ≤ VPIN ≤ VDD

—

± 0.1 ± 5

μA VSS ≤ VPIN ≤ VDD

D063

OSC1

—

± 0.1 ± 5

μA VSS ≤ VPIN ≤ VDD, XT, HS and

LP oscillator configuration

D070 IPUR

PORTA Weak Pull-up

Current

50*

250 400* μA VDD = 5.0V, VPIN = VSS

VOL

Output Low Voltage

D080

I/O ports

—

—

0.6

V IOL = 8.5 mA, VDD = 4.5V (Ind.)

D083

OSC2/CLKOUT (RC mode)

—

—

0.6

V IOL = 1.6 mA, VDD = 4.5V (Ind.)

IOL = 1.2 mA, VDD = 4.5V (Ext.)

*

†

Note 1:

2:

3:

4:

These parameters are characterized but not tested.

Data in ‘Typ’ column is at 5.0V, 25°C unless otherwise stated. These parameters are for design guidance only

and are not tested.

In RC oscillator configuration, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended to use an

external clock in RC mode.

Negative current is defined as current sourced by the pin.

The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels

represent normal operating conditions. Higher leakage current may be measured at different input voltages.

See Section 9.4.1 “Using the Data EEPROM” for additional information.

DS41232B-page 154

Preliminary

© 2005 Microchip Technology Inc.

Share Link: