ADSP-BF516KSWZ-3(RevD) View Datasheet(PDF) - Analog Devices
Part Name
Description
Manufacturer
ADSP-BF516KSWZ-3 Datasheet PDF : 68 Pages
| |||
ADSP-BF512/BF514/BF514F16/BF516/BF518/BF518F16
SPECIFICATIONS
Note that component specifications are subject to change
without notice.
OPERATING CONDITIONS
Parameter
Conditions
Min
Nominal
Max
Unit
VDDINT Internal Supply Voltage
Internal Supply Voltage
Industrial Models
Commercial Models
1.14
1.47
V
1.10
1.47
V
Internal Supply Voltage
Automotive Models
1.33
1.47
V
VDDEXT1, 2 External Supply Voltage
External Supply Voltage
1.8 V I/O, Nonautomotive Models
2.5 V I/O, Nonautomotive Models
1.7
1.8
2.25
2.5
1.9
V
2.75
V
External Supply Voltage
3.3 V I/O, All Models
3.0
3.3
3.6
V
VDDMEM3 MEM Supply Voltage
MEM Supply Voltage
1.8 V I/O, Nonautomotive Models
2.5 V I/O, Nonautomotive Models
1.7
1.8
2.25
2.5
1.9
V
2.75
V
MEM Supply Voltage
3.3 V I/O, All Models
3.0
3.3
3.6
V
VDDRTC4 RTC Power Supply Voltage
VDDFLASH4 Internal SPI Flash Supply
Voltage
2.25
3.6
V
2.7
3.3
3.6
V
VDDOTP1
VPPOTP
OTP Supply Voltage
OTP Programming Voltage
For Reads1
2.25
2.5
2.25
2.5
2.75
V
2.75
V
For Writes5
6.9
7.0
7.1
V
VIH
VIHTWI
VIL
VILTWI
High Level Input Voltage6, 7
High Level Input Voltage6, 8
High Level Input Voltage6, 8
High Level Input Voltage
Low Level Input Voltage6, 7
Low Level Input Voltage6, 8
Low Level Input Voltage6, 8
Low Level Input Voltage
Junction Temperature
Junction Temperature
Junction Temperature
Junction Temperature
VDDEXT/VDDMEM = 1.90 V
1.2
VDDEXT/VDDMEM = 2.75 V
1.7
VDDEXT/VDDMEM = 3.6 V
2
VDDEXT = 1.90 V/2.75 V/3.6 V
0.7 × VBUSTWI
VDDEXT/VDDMEM = 1.7 V
VDDEXT/VDDMEM = 2.25 V
VDDEXT/VDDMEM = 3.0 V
VDDEXT = Minimum
168-Ball CSP_BGA @ TAMBIENT = 0°C to +70°C 0
168-Ball CSP_BGA @ TAMBIENT = –40°C to +85°C –40
176-Lead LQFP_EP @ TAMBIENT = 0°C to +70°C 0
176-Lead LQFP_EP @ TAMBIENT = –40°C to +85°C –40
V
V
V
VBUSTWI9
V
0.6
V
0.7
V
0.8
V
0.3 × VBUSTWI10 V
+95
°C
+105
°C
+95
°C
+105
°C
1 Must remain powered (even if the associated function is not used).
2 VDDEXT is the supply to the GPIO.
3 Pins/balls that use VDDMEM are DATA15–0, ADDR19–1, ABE1–0, ARE, AWE, AMS1–0, SA10, SWE, SCAS, CLKOUT, SRAS, SMS, SCKE. These pins/balls are not tolerant
to voltages higher than VDDMEM. When using any of the asynchronous memory signals AMS3–2, ARDY, or AOE VDDMEM and VDDEXT must be shorted externally.
4 If not used, power with VDDEXT.
5 The VPPOTP voltage for writes must only be applied when programming OTP memory. There is a finite amount of cumulative time that this voltage may be applied (dependent
on voltage and junction temperature) over the lifetime of the part.
6 Parameter value applies to all input and bidirectional pins/balls except SDA and SCL.
7 Bidirectional balls (PF15–0, PG15–0, PH15–0) and input balls (RTXI, TCK, TDI, TMS, TRST, CLKIN, RESET, NMI, and BMODE3–0) of the ADSP-BF51x processors are
2.5 V tolerant (always accept up to 2.7 V maximum VIH). Voltage compliance (on outputs, VOH) is limited by the VDDEXT supply voltage.
8 Bidirectional pins/balls (PF15–0, PG15–0, PH7–0) and input pins/balls (RTXI, TCK, TDI, TMS, TRST, CLKIN, RESET, NMI, and BMODE2–0) of the ADSP-BF51x are
3.3 V tolerant (always accept up to 3.6 V maximum VIH). Voltage compliance (on outputs, VOH) is limited by the VDDEXT supply voltage.
9 The VIHTWI min and max value vary with the selection in the TWI_DT field of the NONGPIO_DRIVE register. See VBUSTWI min and max values in Table 9.
10SDA and SCL are pulled up to VBUSTWI. See Table 9.
Rev. D | Page 22 of 68 | April 2014
Share Link: 